Der RUCKUS Technical Family beitreten

ICX6450 VLAN Dual-mode broken

I have a 6450 firmware ICX64R08030p and I have hit a wall for dual-mode vlans. There seem to be some limitations that a port can only placed in dual-mode if it is still untagged in the default vlan, which makes a big mess if you moved a port to another untagged vlan.I can for instance do this:vlan 5 tagged eth 1/1/20 int eth 1/1/20 dual-mode 1So, starting 1/1/20 was untagged in the default vlan 1, I then tagged it in vlan 5, then went in to the interface and set it to dual-mode vlan 1. All worked as expected, its tagged in 5, untagged in 1. I can even dual-mode 10 and it successfully untags in 10.However - if I go in to eth 1/1/1, which is the uplink port to the next switch, which is where I am programming from ssh. That port is currently untagged in vlan 99, which has a ve 99 with IP for me to program on. Most of the switch is untagged in vlan 1. I want to add several other tagged vlans to 1/1/1, but it does not let me add any.Procedure seems to be the port must be untagged in the default vlan, then you can tag it in as many vlans as you want, then go in to the interface and set it to dual-mode on some other vlan, which makes that the untagged vlan. BUT - you can only tag a port that is currently untagged in vlan 1, if it is untagged in any other vlan you cannot tag it in any other vlan.Note 1/1/1 is already untagged in vlan 99.SSH@ICX6450-48P-Router(config-vlan-5)#tagged eth 1/1/1 error - port ethe 1/1/1 are not member of default vlanIt seems a port must first be untagged in default vlan 1, then it can be tagged in another vlan before it can be dual-mode, but if it is not in default vlan 1 it will never let you set it to dual-mode, nor tag it in any other vlans - it is like the port is locked in 1 vlan in a black hole.

Equivalent (or better) command to Cisco show interface summary

Hey Everyone, I'm looking for an equivalent command line command to the Sho Int Summ from Cisco Switches, the closest thing I've found is Sho Stat which gives a table of statistics for each ethernet interface with the packets and errors in and out.What I'm really looking for is the bits per second or the port utilization for all ports on the switch preferably in a table.I have a webpage I wrote for executing cisco commands we commonly use for troubleshooting/configuration and now that we have some more Ruckus Switches, I'm updating it because the vSZ interface takes a little too long to update sometimes and doesn't get you all of the information I have setup on this page.

Access point - delivering wrong IP

Hello, my name is Filipe, I hope you are well. We have been experiencing a problem with our AP regarding DHCP. The device is handing out IPs, even with the DHCP service disabled. This has directly affected the connection of other devices on our network.My E-mail: dti003@schioppa.com.brI await contact from: dti003@schioppa.com.bror danilo.almeida@digiti.com.br

Spectrum Analysis T750SE and SmartZone

Hi,I am wanting to perform spectrum analysis using T750SE and SmartZone.When trying to start spectrum analysis in the Troubleshooting menu. None of the T750SE available in the menu have checkboxes. Note at bottom of this menu is 'APs without a checkbox do not support spectrum analysis'.The datasheet suggests both the T750 and T750SE support spectrum analysis.https://www.commscope.com/globalassets/digizuite/61785-ds-ruckus-t750.pdfAny support is appreciated.ThanksJames

Inter-VRF-Routing-ICX7750

ICX(config)# vrf client1ICX(config-vrf-client1)# rd 7750:1ICX(config-vrf-client1)# address-family ipv4ICX(config-vrf-client1-af)# exitICX(config)# vrf client2ICX(config-vrf-client2)# rd 7750:2ICX(config-vrf--client2)# address-family ipv4ICX(config-vrf--client2-af)# exitICX(config)# vrf client3ICX(config-vrf-client3)# rd 7750:3ICX(config-vrf--client3)# address-family ipv4ICX(config-vrf--client3-af)# exitICX(config)# vrf client4ICX(config-vrf-client4)# rd 7750:4ICX(config-vrf--client4)# address-family ipv4ICX(config-vrf--client4-af)# exitICX(config)# vlan 550 name client1_vlanICX(config-vlan-550)#router-interface ve 550ICX(config-vlan-550)#interface ve 550ICX(config-vif-550)#vrf forwarding client1ICX(config-vif-550)#ip address 192.168.150.1/24ICX(config)# vlan 550 name client2_vlanICX(config-vlan-551)#router-interface ve 551ICX(config-vlan-551)#interface ve 550ICX(config-vif-551)#vrf forwarding client1ICX(config-vif-551)#ip address 192.168.160.1/24ICX(config)# vlan 1023 name client3_vlanICX(config-vlan-1023)#router-interface ve 1023ICX(config-vif-1023)#vrf forwarding client3ICX(config-vif-1023)#ip address 192.168.110.1/24ICX(config)# vlan 1024 name client4_vlanICX(config-vlan-1024)#router-interface ve 1024ICX(config-vif-1024)#vrf forwarding client3ICX(config-vif-1024)#ip address 192.168.120.1/24ICX(config)# ip route vrf client1 192.168.110.0/24 ve 1023ICX(config)# ip route vrf client2 192.168.120.0/24 ve 1024ICX(config)# ip route vrf client3 192.168.150.0/24 ve 550ICX(config)# ip route vrf client4 192.168.160.0/24 ve 551On checking,the vrf routes,i can see the routes#show ip route vrf <vrf_name>but when i check the ping for example#ping vrf client1 192.168.110.1#ping vrf client2 192.168.120.1#ping vrf client3 192.168.150.1#ping vrf client4 192.168.160.1I am not receiving any ping...is this way of inter-vrf-route from one one vrf to another vrf on the same switch

Ruckus One speed/duplex mismatch

Hello,In Ruckus One we're seeing "incidents" reported of a speed/duplex mismatch between our switches and APs. In this case the switch is a 1G capable 7150 and the AP is a 2.5G capable R650. The switch is doing the max it's capable of but the AP is capable of more and it appears this is generating an alert for something that isn't a misconfiguration, but exepcted.Is there a way to suppress this alert?Vielen Dank!